PT-LB1Vの取扱説明書・マニュアル [全10ページ 0.89MB]
123945.pdf
gizport - 2013-09-07
http://153.127.246.254/.../123945.pdf - 0.89MB
- キャッシュ
3637view
10page / 0.89MB
Display mode Displayresolution(dots)1Scanning frequencyH(kHz)V(kHz)Dot clockfrequency(MHz)Picturequality2Input terminal720 * 480i720 * 576i720 * 480i720 * 576i720 * 483720 * 5761280 * 7201920 * 1080i1920 * 1080640 * 400640 * 480800 * 600832 * 6241024 * 7681280 * 7201280 * 7681280 * 8001152 * 8641152 * 8701280 * 9601280 * 10241400 * 10501440 * 9001600 * 12001680 * 10501920 * 120015.715.615.715.631.531.345.037.533.828.167.556.331.537.931.535.037.937.543.335.237.948.146.953.749.739.648.456.560.068.744.837.139.647.841.349.149.764.067.576.768.760.064.080.091.164.065.155.975.065.374.659.950.059.950.059.950.060.050.060.050.060.050.070.185.159.966.772.875.085.056.360.372.275.085.174.650.160.070.175.085.059.949.849.959.950.060.259.871.274.985.075.160.060.075.085.060.059.959.960.060.059.9--13.513.527.027.074.374.374.374.3148.5148.525.231.525.230.231.531.536.036.040.050.049.556.357.351.965.075.078.894.574.560.565.379.568.069.183.594.2108.0121.5100.0108.0108.0135.0157.5108.0122.4106.5162.0146.3193.3AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAABNTSC/NTSC4.43/PAL-M/PAL60PAL/PAL-N/SECAM525i (480i)625i (576i)525p (480p)625p (576p)750 (720)/60p750 (720)/50p1125 (1080)/60i1125 (1080)/50i1125 (1080)/60p1125 (1080)/50pVESA70VESA85VGA60VGA65VGA72VGA75VGA85SVGA55SVGA60SVGA70SVGA75SVGA85MAC16XGA50XGA60XGA70XGA75XGA85WIDE750 (720)WXGA768WXGA800MXGA70MXGA75MXGA85MAC21MSXGA60SXGA60SXGA75SXGA85SXGA60+WXGA+UXGA60WSXGA+WUXGAVIDEO/S-VIDEOCOMPUTER (RGB/YPBPR)COMPUTER (RGB only)S P E C F I L EPT-LB1VLCD ProjectorAs of May 2011SFL11M0016/10Computer data compatibilityThis projector accepts up to 91 kHz horizontal scanning frequency and 193 MHz dot clock.NOTE: Pixel thinning is applied to signals that exceed a dot clock frequency of 170 MHz. The display resolution of this projector is 1,024 * 768pixels. Input signals that exceed this resolution will be converted to 1,024 * 768 pixels.List of compatible signals1. The "i" appearing after the resolution indicates an interlaced signal. 2. The following symbols are used to indicate picture quality.AA Maximum picture quality can be obtained. A Signals are converted by the image processing circuit before picture is projected.B Signals are compressed by the image processing circuit before picture is projected.
参考になったと評価
7人が参考になったと評価しています。