5
rb1552-1582_manual.pdf
moreau1996 - 2013-10-05
http://www.rotel.com/.../rb1552-1582_manual.pdf - 2.35MB - キャッシュ
17747view
48page / 2.35MB
8RB-1552 / RB-1582 Stereo Power Ampliier12V Trigger Input and Output 4 The jack labeled IN is for connecting the 3.5mm Plug/Cable carrying a +12 volt trigger signal to turn the ampliier on and off. To use this feature the toggle switch must be set to the ON position. This input accepts any control signal (AC or DC) ranging from 3 volts to 30 volts.The jack labeled OUT is for connecting another 3.5mm plug/cable to provide a 12V trigger signal to other components. The 12V output signal is available whenever a +12 volt trigger signal is applied to the IN connector.Protection Circuitry 2 The RB-1552 and RB-1582 feature thermal and over-current protection circuits that protect against potential damage in the event of extreme or faulty operating conditions. Unlike many designs, these protection circuits are independent of the audio signal and have no impact on sonic performance. Instead, the protection circuits monitors the temperature of the output devices and the current they are handling and shuts down the ampliier if operating conditions exceed safe limits.Most likely, you will never see this protection circuitry in action. However, should a faulty condition arise, the ampliier will stop playing and the LED indicator on the front panel will light up.If this happens, turn the ampliier off, let it cool down for several minutes, and attempt to identify and correct the problem that caused the protection circuitry to engage. When you turn the ampliier back on, the protection circuit will automatically reset and the indicator LED should go out.In most cases, the protection circuitry activates because of a fault condition such as shorted speaker wires, or inadequate ventilation leading to an overheating condition. In very rare cases, highly reactive or extremely low impedance speaker loads could cause the protection circuit to engage.If the protection circuitry triggers repeatedly and you are unable to isolate and correct the faulty condition, contact your authorized Rotel dealer for assistance in troubleshooting.Input Signal Connections 5 The RB-1552 and RB-1582 have conventional RCA type input connectors, the type found on nearly all audio equipment. Note: To prevent loud potentially damaging noises, make sure the amplifier is turned off when you make any changes to the input signal configuration.Select high quality audio interconnect cables. Connect each of the outputs from the preampliier or signal processor to the corresponding input of the ampliier. Speaker ConnectionSpeaker SelectionWe recommend using loudspeakers with a nominal impedance of 4 ohms or higher with the RB-1552 and RB-1582. You should exercise some caution in driving multiple pairs of speakers in parallel coniguration, because the effective impedance the ampliier sees is cut in half. For example, when driving two pair of 8 ohm speakers, the ampliier sees a 4 ohm load. When driving multiple speakers in parallel, it is recommended that you select speakers with a nominal impedance of 8 ohms or higher. Speaker impedance ratings are less than precise. In practice, very few loudspeakers will present any problems for the RB-1552 or RB-1582. See your authorized Rotel dealer if you have any questions.Speaker Wire SelectionUse insulated two-conductor stranded wire to connect the ampliier to the speakers. The size and quality of the wire can have an audible effect on the performance of the system. Standard speaker wire will work, but can result in lower output or diminished bass response, particularly over longer distances. In general, heavier wire will improve the sound. For best performance, you may want to consider special high-quality speaker cables. Your authorized Rotel dealer can help in the selection of appropriate cables for your system.Polarity and PhasingThe polarity — the positive/negative orientation of the connections — for every speaker and ampliier connection must be consistent so all the speakers will be in phase. If the polarity of one connection is mistakenly reversed, bass output will be very weak and stereo imaging degraded. All wire is marked so you can identify the two conductors. There may be ribs or a stripe on the insulation of one conductor. The wire may have clear insulation with different color conductors (copper and silver). There may be polarity indications printed on the insulation. Identify the positive and negative conductors and be consistent with every speaker and ampliier connection.Speaker Connection 6 The RB-1552 and RB-1582 have four pairs of color coded binding posts, two for each channel. These connectors accept bare wire, connector lugs, or dual banana type connectors (except in the European Community countries where their use is not permitted). Route the wire from the ampliier to the speakers. Give yourself enough slack so you can move the components enough to allow access to the speaker connectors.If you are using dual banana plugs, connect them to the wires and then plug into the backs of the binding posts. The binding posts should be screwed in all the way (clockwise).If you are using terminal lugs, connect them to the wires. If you are attaching bare wires directly to the binding posts, separate the wire conductors and strip back the insulation from the end of each conductor. Be careful not to cut into the wire strands. Unscrew (turn counterclockwise) the binding post. Place the connector lug or wire around the binding post shaft. Turn the binding post clockwise to clamp the connector lug or wire irmly in place. Note: Be sure there are no loose wire strands that could touch adjacent wires or connectors.
