REAR L-SHAPED LOUNGE TO DOUBLE BED (170-POPULAR AND 190-VERSATILE)To convert the lounge into a double bed:i) Remove cushion under TV cabinet and store.ii) Remove small rear back rest cushion on driver side and store.iii) Remove table top,rotate,place on ledges between seats,and slide to front against rubber stops.iv) Remove small narrow board stored along wall under TV cabinet and place behind the table top.v) Lift the rear back rest cushion up from the bottom and open rear door.vi) Remove this cushion by detaching Velcro found on back flap of backrest board and close rear door.vii) Rotate rear seat cushion 90 degrees and place in the middle section with cushion running front to back.viii)With the rear back cushion in hand,separate the Velcro at the bottom edge of the cushion.ix) Spread this cushion flat and lay it on the driver side next to the seat cushions with Velcro down.x) Do the same with the passenger side back rest cushion by pulling the Velcro apart at the top edge of thecushion,and lay it on top of the other back rest cushion with Velcro up.To convert back to a lounge,perform these steps in reverse order.REAR L-SHAPED LOUNGE TO DOUBLE BED (200-VERSATILE)To convert the lounge into a double bed:i) Remove cushion under TV cabinet and store.ii) Remove small rear back rest cushion on driver side and store.iii) Remove table top,rotate,place on ledges between seats,and slide to front against rubber stops.iv) Remove small narrow board stored along wall under TV cabinet and place behind the table top.v) Remove the rear back rest cushion and place temporarily on the passenger side seat cushion.vi) Turn rear seat cushion counterclockwise 90 degrees and place in the middle section with cushionrunning front to back.vii) With the rear back cushion in hand,separate the Velcro at the bottom edge of the cushion.viii)Spread this cushion flat and lay it on the driver side next to the seat cushions with Velcro down.ix) Do the same with the passenger side back rest cushion by pulling the Velcro apart at the top edge of thecushion,and lay it on top of the other back rest cushion with Velcro up.To convert back to a lounge,perform these steps in reverse order.DAILY LIVINGDoc No:MNSA0006 Rev:00Copyright(C) Hanmar Motor Corporation 203 B-1SLEEPING FACILITIES:REAR L-SHAPED LOUNGE TO DOUBLE BED (170-POPULAR AND 190-VERSATILE)To convert the lounge into a double bed:i) Remove cushion under TV cabinet and store.ii) Remove small rear back rest cushion on driver side and store.iii) Remove table top,rotate,place on ledges between seats,and slide to front against rubber stops.iv) Remove small narrow board stored along wall under TV cabinet and place behind the table top.v) Lift the rear back rest cushion up from the bottom and open rear door.vi) Remove this cushion by detaching Velcro found on back flap of backrest board and close rear door.vii) Rotate rear seat cushion 90 degrees and place in the middle section with cushion running front to back.viii)With the rear back cushion in hand,separate the Velcro at the bottom edge of the cushion.ix) Spread this cushion flat and lay it on the driver side next to the seat cushions with Velcro down.x) Do the same with the passenger side back rest cushion by pulling the Velcro apart at the top edge of thecushion,and lay it on top of the other back rest cushion with Velcro up.To convert back to a lounge,perform these steps in reverse order.REAR L-SHAPED LOUNGE TO DOUBLE BED (200-VERSATILE)To convert the lounge into a double bed:i) Remove cushion under TV cabinet and store.ii) Remove small rear back rest cushion on driver side and store.iii) Remove table top,rotate,place on ledges between seats,and slide to front against rubber stops.iv) Remove small narrow board stored along wall under TV cabinet and place behind the table top.v) Remove the rear back rest cushion and place temporarily on the passenger side seat cushion.vi) Turn rear seat cushion counterclockwise 90 degrees and place in the middle section with cushionrunning front to back.vii) With the rear back cushion in hand,separate the Velcro at the bottom edge of the cushion.viii)Spread this cushion flat and lay it on the driver side next to the seat cushions with Velcro down.ix) Do the same with the passenger side back rest cushion by pulling the Velcro apart at the top edge of thecushion,and lay it on top of the other back rest cushion with Velcro up.To convert back to a lounge,perform these steps in reverse order.
