REAR DINETTE TO DOUBLE BED (190-VERSATILE)To convert the dinette into a double bed:i) Remove the table and legs from their bases and place the table on the lateral supports located on theupper edge of the seat base boxes.ii) Starting on the driver side,move the seat cushion to the passenger side.iii) Pull the driver side back rest cushion inward and down until it lies flat.iv) Push this cushion out against the interior wall of your vehicle.v) Move both seat cushions over to the left side and repeat the fourth step with the passenger back restcushion.vi) Place the inner edges of the two seat cushions together and lay them flat.To convert back to a dinette,perform these steps in reverse order.REAR TWIN BEDS (190-POPULAR AND 200-POPULAR)To convert the dinette into twin beds:i) Remove the table and leg from its receptacle and place the table under the driver side seat cushion.ii) Place both back rest cushions on the floor vertically up against the seat base boxes.iii) Pull each seat cushion 3" (8 cm) from the wall to provide additional elbow room while sleeping.iv) Night table can be removed and stored if desired.To convert back to a dinette,perform these steps in reverse order.REAR KING-SIZE BED (190-POPULAR AND 200-POPULAR)To convert the dinette into a king-size bed:i) Remove the privacy curtain from its Velcro support on the lower edge of the suspended cupboard.ii) Remove the table and leg from its receptacle.iii) Lift the front of the night table,pull forward,remove,and store.iv) Raise seat cushions and flip hinged bed support forward.v) Place the table on the lateral supports of the seat base boxes as far to the front as the supports allow.vi) Slide the driver side seat cushion in toward the center of your vehicle.vii) Place the driver side large back rest cushion against the wall and as far to the rear as possible.viii)Place the small cushion against the wall and as far to the front as possible (below suspended cupboardor pantry).ix) Slide the driver side seat cushion out toward the wall of your vehicle against the edges of the back restcushions.x) Repeat the fourth to seventh steps on the passenger side.xi) Place the inner edges of two seat cushions together and lay them flat.To convert back to a dinette,perform these steps in reverse order.DAILY LIVINGDoc No:MNSA0006 Rev:00Copyright(C) Hanmar Motor Corporation 203 B-2REAR DINETTE TO DOUBLE BED (190-VERSATILE)To convert the dinette into a double bed:i) Remove the table and legs from their bases and place the table on the lateral supports located on theupper edge of the seat base boxes.ii) Starting on the driver side,move the seat cushion to the passenger side.iii) Pull the driver side back rest cushion inward and down until it lies flat.iv) Push this cushion out against the interior wall of your vehicle.v) Move both seat cushions over to the left side and repeat the fourth step with the passenger back restcushion.vi) Place the inner edges of the two seat cushions together and lay them flat.To convert back to a dinette,perform these steps in reverse order.REAR TWIN BEDS (190-POPULAR AND 200-POPULAR)To convert the dinette into twin beds:i) Remove the table and leg from its receptacle and place the table under the driver side seat cushion.ii) Place both back rest cushions on the floor vertically up against the seat base boxes.iii) Pull each seat cushion 3" (8 cm) from the wall to provide additional elbow room while sleeping.iv) Night table can be removed and stored if desired.To convert back to a dinette,perform these steps in reverse order.REAR KING-SIZE BED (190-POPULAR AND 200-POPULAR)To convert the dinette into a king-size bed:i) Remove the privacy curtain from its Velcro support on the lower edge of the suspended cupboard.ii) Remove the table and leg from its receptacle.iii) Lift the front of the night table,pull forward,remove,and store.iv) Raise seat cushions and flip hinged bed support forward.v) Place the table on the lateral supports of the seat base boxes as far to the front as the supports allow.vi) Slide the driver side seat cushion in toward the center of your vehicle.vii) Place the driver side large back rest cushion against the wall and as far to the rear as possible.viii)Place the small cushion against the wall and as far to the front as possible (below suspended cupboardor pantry).ix) Slide the driver side seat cushion out toward the wall of your vehicle against the edges of the back restcushions.x) Repeat the fourth to seventh steps on the passenger side.xi) Place the inner edges of two seat cushions together and lay them flat.To convert back to a dinette,perform these steps in reverse order.
