20English4 Select the music source.1. Press the TIMER button on the Unit."TUNER" flashes on the display.2. Press the c or 4 button to select the music source youwant to listen to.The display changes as shown below.5 Set the volume level.1. Press the TIMER button on the Unit.The current volume setting flashes on the display.2. Press the c or 4 button to select the volume level.-- : The current volume level will be used.0 to 40 : When the timer is turned on, the Volume willbe automatically set to the selected level.6 Press the TIMER button on the Unit.The timer setting is completed and the display returns to the indi-cations before you set the timer. The Timer indicator remains lit.7 Before turning off the System, preparethe music source selected in step 4.TUNER: Tune in to the desired station.REC TUNER: See "Setting the Recording Timer".CD: Insert a CD.TAPE: Insert a tape.8 Press the button to turn off the Sys-tem.To cancel the timer, press the TIMER button for more than 2seconds. The Timer indicator goes out on the display.To re-activate the canceled timer, press the TIMER button formore than 2 seconds to light the Timer indicator. Then, press theTIMER button until the display returns to the previous indications.The Timer indicator should remain lit.To confirm the timer settings, cancel the timer once bypressing the TIMER button, and press the button again for morethan 2 seconds. Then, press the TIMER button repeatedly, to seethe current timer settings (ON time, OFF time, source, andvolume). Press the TIMER button to set the timer again.To change the timer setting, repeat the setting procedure fromthe beginning.* When the timer turns on, the Timer indicator starts flashing.Note:If the Unit is turned on when the timer-on time comes,Daily Timer does not work.CAUTION:If the System is unplugged, or a power failureoccurs, the timer will be canceled. You will needto reset the clock first, then the timer.Setting the Recording TimerWith the Recording Timer, you can make a tape of radio broadcastautomatically.How Recording Timer actually worksThe Unit automatically turns on, tunes into the last received station,and starts recording when the on-time comes. Then, when the off-time comes, the Unit automatically turns off (stands by).The timer setting remains in memory until you change it.Notes:* Finish each step within 30 seconds. Otherwise, the setting iscleared and the procedure must be repeated from the beginning.* The clock must be correctly set for the timers to work.If the clock has not been set, the CLOCK indicator will flashon the display when you press the TIMER button for more than2 seconds, and then the display alternates between "ADJUST"and "CLOCK" for about 5 seconds.1 Press the button to turn on the Sys-tem.2 Tune in to the desired station.See page 8.3 Press the TIMER button on the Unit formore than 2 seconds.The ON indicator lights up, and then the current ON timeflashes on the display. (Example: 12:00)4 Set the ON time. (Example: 12:15)Press the c or 4 button on the Unit to set the hour youwant the Unit to come on.Pressing the c button moves the hour forwards and pressingthe 4 button moves it backwards. Hold down the button tomove the hour rapidly. Press the TIMER button to adjust theminute.5 Set the OFF time. (Example: 13:15)1. Press the TIMER button on the Unit.The hour digits of the current OFF time flashes, and thenthe OFF indicator lights up on the display.2. Press the c or 4 button on the Unit to set the time youwant the Unit to be turned off.Pressing the c button moves the hour forwards andpressing the 4 button moves it backwards. Hold downthe button to move the hour rapidly. Press the TIMERbutton again to adjust the minute.6 Press the TIMER button on the Unit.ONSLEEPONSLEEPOFFSLEEPOFFSLEEPSLEEPEN12-22.UX-V10/V20R[E] 00.1.20, 7:04 PM 20
参考になったと評価 11人が参考になったと評価しています。
関連サポート製品
Copyright © 2013 Gizport.jp All Rights Reserved.
