1. 取扱説明書・マニュアル >
2. パナソニック >
3. パソコン >
4. パソコン周辺機器 >
5. プロジェクタ >
6. PT-LB90NT の使い方、故障・トラブル対処法 >
7. PT-LB90NT の取扱説明書・マニュアル

PT-LB90NTの取扱説明書・マニュアル [全68ページ 8.58MB]

Precautions with regard to safetyImportant Information8 - ENGLISHON USE/INSTALLATION „Do not put your weight on this projector.You could fall or the projector could break, and injury will result.Be especially careful not to let young children stand zor sit on the projector.Do not place the projector in extremely hot locations.Doing so will cause the outer casing or internal com -ponents to deteriorate, or result in ire.Take particular care in locations exposed to direct zsunlight or near stoves.Always disconnect all cables before mov-ing the projector.Moving the projector with cables still attached can damage the cables, which will cause ire or electric shocks to occur.ACCESSORIES „Do not use the old lamp unit.If used it could cause lamp explosion.If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces.Failure to observe this will cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as luorescent lamps, and the broken pieces will cause injury.If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medi -cal advice immediately.Ask your dealer about replacing the lamp unit and check the inside of the projector.Do not use projectors with the adjustable feet or lens cover removed.If this not observed, the sets will not operate correctly or accidents will result.Cautions when transportingWhen transporting the projector, the adjuster legs must be housed and do not hold them. Please se -curely hold only its bottom and none of its other parts or surfaces as this will result in malfunctions.When transporting, keep the projector in the provided carrying bag.Face the lens of the projector in an upward direc - ztion and put it gently into the carrying bag.Do not put anything other than the projector and its zaccessories in the carrying bag.Cautions when installingDo not use under the following „conditions.Do not set up the projector outdoors. zThe projector is designed for indoor use only.Avoid setting up in places which are subject to zvibration or shocks.If the projector is installed in a place where vibra -tions are transmitted or mounted in a car or a ves -sel, vibrations or impacts will result in damage to the internal parts, causing failure. Install the product in a place free from vibrations and impacts.Avoid setting up in places which are subject to zsudden temperature changes, such as near an air conditioner or lighting equipment.Failure to observe this will result in malfunctions or the lamp life will be shortened.See “TEMP indicator” on page 4 6.Avoid setting up in places which are near high- zvoltage power lines or near motors.The product will be exposed to interference if it is installed in the vicinity of high-voltage electrical power lines or power sources. zDo not install the projector at elevations higher than 2 700 m (8 858 ft) above sea level.If using this projector at high elevations 1 400 - 2 700 m (4 593 - 8 858 ft) above sea level, set the HIGH ALTITUDE MODE to ON.Failure to observe this will result in malfunctions or the lamp life or life of other components will be shortened.Be sure to ask a specialised tech- „nician when installing the product to a ceiling.If the product is to be installed hanging from the ceil -ing, purchase an optional hanging attachment (Model No. ET-PKB80). Please call a specialised technician or contact an Authorized Service Center for installa -tion.Lens Focus „Do not adjust the lens focus in the initial period after switching the projector on. The high clarity projector lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on. Please allow a warm-up time of at least 30 minutes before adjusting the lens focus.

このマニュアルの目次

Copyright © 2013 Gizport.jp All Rights Reserved.