"XPS"10 - 20 件目を表示
"XPS"22 件の検索結果
全般
質問者が納得あやしいですけど、それしか方法がないですよね。
たぶん内蔵ドライブは調子悪いと思いますよ。普通そういう状態にはなりませんので。
Dドライブにリカバリディスクの内容をコピーして、USBメモリをDOSで起動するように設定して
ハードディスクのDにアクセスしてセットアップをコマンドで実行する・・・
なんてのはダメでしょうかね？
5101日前view101
全般
質問者が納得外付けのCDドライブはUSB接続と思いますが、BIOSの起動ドライブをHDDより上位にUSBを設定し、再セットアップCDをドライブに入れた状態で電源Onをしてください。これで再セットアップメニューが起動すれば再セットアップは出来ます。起動しないときはあきらめるより外ないです。
補足への回答
BIOS起動は電源Onと同時にF-2を押し続けて下さい。
5113日前view39
全般
質問者が納得http://orbit.cocolog-nifty.com/supportdiary/2009/12/post-a9ef.html
5318日前view128
全般
質問者が納得一度ケーブルの抜き差しを行ってみては如何ですか？
フレキシブルケーブルが抜けかかっているとかはありませんか？
にしても、ここ数年のDELLはひどいですね・・・
5348日前view93
Dell™ XPS™ M1210 Service Manual Before You BeginCoin-Cell BatteryOptical DrivePalm RestHard DriveModemMemory Module(s)Processor ModuleHinge CoverFanKeyboardThermal-Cooling AssemblyMini-CardsHard Drive Bay/ExpressCard Cage AssemblyInternal Card With Bluetooth® Wireless TechnologySystem BoardDisplayFlashing the BIOSCamera (Optional)Pin Assignments for I/O Connectors Notes, Notices, and CautionsNOTE: A NOTE indicates important information that helps you make better use of your computer.NOTICE: A NOTICE indica...
Back to Contents Page Before You BeginDell™ XPS™ M1210 Service Manual Recommended Tools Turning Off Your Computer Before Working Inside Your ComputerThis section provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that thefollowing conditions exist:l You have performed the steps in Turning Off Your Computer and Before Working Inside Your Computer.l You have read the safety information in the Dell™ Product Information Guide.l A c...
Back to Contents Page ModemDell™ XPS™ M1210 Service Manual Removing the Modem Replacing the Modem Removing the Modem CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (suchas the back panel) on the computer.NOTICE: To help prevent damage to the system board, remove the main battery (see Before Wor...
Back to Contents Page FanDell™ XPS™ M1210 Service Manual CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (suchas the back panel) on the computer.NOTICE: To help prevent damage to the system board, remove the main battery (see Before Working Inside Your Computer) before working inside thecomputer.1...
Back to Contents Page Pin Assignments for I/O ConnectorsDell™ XPS™ M1210 Service Manual USB Connector Video Connector S-Video TV-Out Connector IEEE 1394 Connector USB Connector Pin Signal1USB5V+2USBP–3USBP+4GND Video Connector Pin Signal Pin Signal1CRT_R 95V+2CRT_G 10GND3CRT_B 11MONITOR_DETECT–4NC12DDC_DATA5GND13CRT_HS6GND14CRT_VS7GND15DDC_CLK8GND S-Video TV-Out Connector S-Video Pin Signal1GND
Back to Contents Page Hard DriveDell™ XPS™ M1210 Service Manual Removing the Hard Drive Replacing the Hard Drive Returning a Hard Drive to Dell Removing the Hard Drive CAUTION: If you remove the hard drive from the computer when the drive is hot, do not touch the metal housing of the hard drive. CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.NOTICE: To help prevent damage to the system board, remove the main battery (see Before Working ...
Back to Contents Page Flashing the BIOSDell™ XPS™ M1210 Service ManualNOTICE: Plug the AC adapter into a known good power source to prevent a loss of power. Failure to do so may cause system damage.1. Ensure that the AC adapter is plugged in and that the main battery is installed properly.NOTE: If you use a BIOS update program CD to flash the BIOS, press <F12> before inserting the CD so that you can set up the computer to boot from aCD this one time only. Otherwise, you must enter the system setup program ...
Back to Contents Page System BoardDell™ XPS™ M1210 Service Manual Removing the System Board Replacing the System Board Removing the System Board CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (suchas the back panel) on the computer.NOTICE: To help prevent damage to the system board, remove the ...
Back to Contents Page DisplayDell™ XPS™ M1210 Service Manual Display Assembly Display Bezel Display Panel Display-Panel Brackets Display Assembly Removing the Display Assembly CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (suchas the back panel) on the computer.NOTICE: To help prevent damage...
Back to Contents Page Palm RestDell™ XPS™ M1210 Service Manual Removing the Palm Rest Replacing the Palm Rest Removing the Palm Rest CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide.NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (suchas the back panel) on the computer.NOTICE: To help prevent damage to the system board, remove the main battery...
- 1
- 2
