WASTE WATER STORAGE AND DUMPING SYSTEMYour vehicle is equipped with a waste water storage and dumping system that will provide adequate and effectivestorage and dumping of waste water. Your vehicle should be as level as possible to allow optimal operation of thesystem.CAUTION:Ensure that both the black and grey water gate valves,located behind the small access door below thedriver step well,are closed (inward position) before using the waste water system. This applies especially afterextensive driving.Waste Tank Preparation Your vehicle is equipped with two waste water tanks;the grey water tank is for waste water from the sink and aisleshower and the black water tank is for sewage from the toilet. Both tanks are equipped with separate dump valvesso that each may be dumped independently. Before use of either waste tank,be sure to read instructions providedby the toilet manufacturer regarding waste water chemicals. We suggest that such chemicals be used every timeto minimize build up of solids on water level sensors inside the tanks.Waste Tank Dumping Waste water tank contents must be dumped in authorized facilities only. To completely clear the waste water tanksof all solid material,tanks should be full to provide the necessary volume required for complete dumping. If youwish to dump a partially full tank,it is advisable to fill the remaining volume with water first. Also,to completelyclear the tanks of all solid material,tanks should be dumped immediately after road travel while tank contents areunsettled.To dump the black water tank:i) Ensure that the lower "T" shaped black water gate valve handle is closed (inward position).ii) Remove the small cap located on the front of the sewage hose assembly and swing the support arm sothat the assembly can be pulled out.iii) Remove the assembly cover.iv) Connect the dump fitting (stored in the storage compartment behind the large access door) to the endof the assembly.v) Securely place the dump fitting and assembly in the local waste receptacle.vi) Pull the black water gate valve handle to dump the tank contents.vii) Once the tank is empty,close the gate valve,remove the fitting,return the assembly to its supportstructure and ensure that all caps and supports are securely in place.To dump the grey water tank:i) Follow the same procedure using the inner grey water gate valve handle located above the black watergate valve handle.ii) Be sure to dump the grey water tank last so as to help flush out any solid waste in the sewage hose fromthe black water tank.iii) If desired,flush both waste tanks after dumping.WATER SYSTEMDoc No:MNSA0006 Rev:00Copyright(C) Hanmar Motor Corporation 203 E-2WASTE WATER STORAGE AND DUMPING SYSTEMYour vehicle is equipped with a waste water storage and dumping system that will provide adequate and effectivestorage and dumping of waste water. Your vehicle should be as level as possible to allow optimal operation of thesystem.CAUTION:Ensure that both the black and grey water gate valves,located behind the small access door below thedriver step well,are closed (inward position) before using the waste water system. This applies especially afterextensive driving.Waste Tank Preparation Your vehicle is equipped with two waste water tanks;the grey water tank is for waste water from the sink and aisleshower and the black water tank is for sewage from the toilet. Both tanks are equipped with separate dump valvesso that each may be dumped independently. Before use of either waste tank,be sure to read instructions providedby the toilet manufacturer regarding waste water chemicals. We suggest that such chemicals be used every timeto minimize build up of solids on water level sensors inside the tanks.Waste Tank Dumping Waste water tank contents must be dumped in authorized facilities only. To completely clear the waste water tanksof all solid material,tanks should be full to provide the necessary volume required for complete dumping. If youwish to dump a partially full tank,it is advisable to fill the remaining volume with water first. Also,to completelyclear the tanks of all solid material,tanks should be dumped immediately after road travel while tank contents areunsettled.To dump the black water tank:i) Ensure that the lower "T" shaped black water gate valve handle is closed (inward position).ii) Remove the small cap located on the front of the sewage hose assembly and swing the support arm sothat the assembly can be pulled out.iii) Remove the assembly cover.iv) Connect the dump fitting (stored in the storage compartment behind the large access door) to the endof the assembly.v) Securely place the dump fitting and assembly in the local waste receptacle.vi) Pull the black water gate valve handle to dump the tank contents.vii) Once the tank is empty,close the gate valve,remove the fitting,return the assembly to its supportstructure and ensure that all caps and supports are securely in place.To dump the grey water tank:i) Follow the same procedure using the inner grey water gate valve handle located above the black watergate valve handle.ii) Be sure to dump the grey water tank last so as to help flush out any solid waste in the sewage hose fromthe black water tank.iii) If desired,flush both waste tanks after dumping.
